Lighting & Controls
Wattstopper Lighting Controls: Installation, Service & Repair
Whole-building Wattstopper Digital Lighting Management systems, installed, programmed and integrated with your building automation system, plus service and repair for the systems already on your walls.
Wattstopper is one of the most common lighting control platforms in Colorado's commercial buildings, schools and government facilities. EVO holds Legrand Wattstopper lighting-controls credentials and specialises in whole-building Wattstopper systems: designing the layout, installing every device, programming the sequence of operations, tying it into the building automation system, and keeping it working afterwards.
Whole-building Wattstopper DLM
Wattstopper's Digital Lighting Management (DLM) platform scales from a single room to a full building. We install and configure every layer of it:
- DLM room controllers, occupancy and vacancy sensors, daylight sensors and digital switches in each space
- LMCP lighting control panels for corridors, common areas, exterior and scheduled loads
- Network bridges and segment networks that tie rooms and panels into one building system
- Scheduling, timeclock and holiday control from a central network controller
- Plug load control where energy code requires it
- Wired and wireless devices, so retrofits don't mean pulling new control wire everywhere
Integration with your building automation system
DLM networks speak BACnet, so the BAS can see occupancy, override lighting and share schedules with HVAC. We coordinate the integration points with your controls contractor during submittals, set the BACnet addressing, and verify the points are live before turnover, so integration isn't left as an open item at the end of the job.
Wattstopper service and repair
A lot of Wattstopper systems in Colorado were installed years ago, programmed once and never touched again. Rooms got remodelled, devices were replaced with the wrong part, and nobody has the programming records. We fix that.
- Troubleshooting lights that won't turn on, won't turn off or switch off on people
- Replacing failed room controllers, sensors, switches and panel relays
- Reprogramming sensor timeouts, daylight setpoints, schedules and scene buttons
- Recovering networks with lost addressing or broken segment wiring
- Re-commissioning after remodels and tenant improvements
- Upgrading older Wattstopper components that are no longer supported
- Documenting the system as it actually exists, so the next service call is faster
We're open 24/7, so a control failure that leaves a building dark, or lit all night, gets an electrician the same day.
Energy code and commissioning
Colorado's energy codes require automatic shutoff, occupancy sensing, daylight-responsive control and multi-level lighting in most commercial spaces. A Wattstopper system meets them only if it's programmed to the engineer's sequence of operations and tested. We do the functional testing and give you the documentation the inspector and commissioning agent will ask for. See energy code compliance and commissioning.
We also install Acuity nLight and other platforms; see networked lighting controls.
Common questions
Do you service Wattstopper systems someone else installed?
Yes. Much of our Wattstopper work is troubleshooting, repairing and reprogramming systems another contractor installed, often with no programming records left behind.
Our lights turn off while people are still in the room. Can you fix that?
Usually in one visit. It's normally sensor coverage, placement or timeout settings. We adjust the settings, move or add sensors where needed, and test the space with people in it.
Can Wattstopper connect to our building automation system?
Yes. Wattstopper DLM networks communicate over BACnet, so your BAS can see occupancy and schedules and override lighting. We coordinate the integration points with your controls contractor.
Can you add Wattstopper controls to an existing building?
Yes. Wireless DLM devices and room controllers let us add occupancy sensing, daylighting and scheduling without rewiring every space.
Are you available for emergency lighting-control failures?
Yes. We're open 24/7. If a control failure leaves a building dark or stuck on, call (720) 603-8665.
Ready to talk about your project?
Tell us what you need and we will give you a straight answer on scope, schedule and cost. No obligation, and no pressure if it turns out we are not the right fit.